Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
5.1. Features of a design
5.2. Compression check in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in position ВМТ of a step of compression
5.6. Removal, installation and дефектовка a flywheel
5.7. Replacement of details of consolidation of the engine
5.8. A head of the block of cylinders
5.9. Removal and engine installation
5.10. Engine repair
5.11. Greasing system
5.12. Cooling system
5.13. System of release of the fulfilled gases
5.14. The engine power supply system
5.14.1. Features of a design
5.14.2. Pressure check in the engine power supply system
5.14.3. Pressure decrease in the power supply system
5.14.4. Removal and installation of the air filter, the muffler of noise of an admission and an air line
5.14.5. Replacement of the fuel pump
5.14.6. Replacement of a fuel tank and its bulk pipe
5.14.7. Check and replacement of a regulator of pressure of fuel
5.14.8. Removal and installation of a fuel stage
5.14.9. Removal, installation and check of atomizers
5.14.10. Removal and installation of throttle knot
5.14.11. Check and replacement of a regulator of idling
5.14.12. Adjustment and replacement of a cable of a drive throttle заслонки
5.14.13. Removal and installation of a pedal of an accelerator
5.15. System of catching of steams of fuel
5.16. System рециркуляции the fulfilled gases
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 



cf8e4909





5-14-9-snyatie-ustanovka-i-proverka-forsunok.html

5.14.9. Removal, installation and check of atomizers

Signs of malfunction of atomizers:
– The complicated start-up of the engine;
– Unstable work of the engine;
– The engine глохнет idling;
– The raised frequency of rotation of a cranked shaft idling;
– The engine does not develop a total power, insufficient приемистость the engine;
– Jerks and failures in engine work at car movement;
– The raised expense of fuel;
– The raised maintenance WITH and СН in the fulfilled gases;
калильное ignition because of негерметичности atomizers.
It be required to you: a screw-driver with a flat edge, an autotester.
1. Preliminary check up serviceability of windings of atomizers. For this purpose disconnect from atomizers колодки a plait of wires, having shifted upwards their spring clamps.
2. Check up resistance of a winding of an atomizer. At a serviceable atomizer it should be 12,5–13,5 Ohm. If resistance of a winding does not correspond to norm, replace an atomizer, as it неремонтопригодна.
    
THE NOTE
Check of atomizers under the form of a sprayed torch of fuel and on tightness spend at specialised servicing deports, as such check directly on the car very much пожароопасна.

3. Remove a fuel stage (Removal and installation of a fuel stage see).
4. Hook a screw-driver …
5. … also remove an atomizer clamp.
6. Take a shaft of an atomizer from a stage aperture. Similarly remove other atomizers.
    
THE NOTE
Pay attention to marks of atomizers. New atomizers get with the same marks.

7. At each removal of atomizers necessarily replace on all atomizers top …
8. … and the bottom sealing rings.
9. If establish former atomizers, accurately wash out their sprays solvent or a carburettor cleaner.

THE PREVENTION
Washing of atomizers окунанием in washing structure as their electric part will be thus damaged is not supposed.

10. Establish atomizers in an order, the return to removal. Before installation of atomizers grease sealing rings with engine oil.
11. Having established atomizers in a fuel stage, and a stage on an inlet pipe and having connected pipelines to a stage, start up the engine and check up tightness of connection of the pipeline and consolidations of atomizers.

The previous page
5.14.8. Removal and installation of a fuel stage
The following page
5.14.10. Removal and installation of throttle knot