Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
5.1. Features of a design
5.2. Compression check in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in position ВМТ of a step of compression
5.6. Removal, installation and дефектовка a flywheel
5.7. Replacement of details of consolidation of the engine
5.8. A head of the block of cylinders
5.9. Removal and engine installation
5.10. Engine repair
5.11. Greasing system
5.12. Cooling system
5.13. System of release of the fulfilled gases
5.14. The engine power supply system
5.14.1. Features of a design
5.14.2. Pressure check in the engine power supply system
5.14.3. Pressure decrease in the power supply system
5.14.4. Removal and installation of the air filter, the muffler of noise of an admission and an air line
5.14.5. Replacement of the fuel pump
5.14.6. Replacement of a fuel tank and its bulk pipe
5.14.7. Check and replacement of a regulator of pressure of fuel
5.14.8. Removal and installation of a fuel stage
5.14.9. Removal, installation and check of atomizers
5.14.10. Removal and installation of throttle knot
5.14.11. Check and replacement of a regulator of idling
5.14.12. Adjustment and replacement of a cable of a drive throttle заслонки
5.14.13. Removal and installation of a pedal of an accelerator
5.15. System of catching of steams of fuel
5.16. System рециркуляции the fulfilled gases
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 








5-14-12-regulirovka-i-zamena-trosa-privoda-drosselnojj-zaslonki.html

5.14.12. Adjustment and replacement of a cable of a drive throttle заслонки

If adjustment of a drive throttle заслонки it is impossible to achieve full opening or closing throttle заслонки or a drive заедает, replace a cable of a drive throttle заслонки.
It be required to you: a screw-driver, пассатижи.
1. For the visual control of moving throttle заслонки ослабьте a collar of fastening also disconnect воздухоподводящий a sleeve from a branch pipe of throttle knot (Removal and installation of throttle knot »see«).
2. At completely pressed pedal of an accelerator (it the assistant should make) check up position throttle заслонки — it should be completely open, and at the released pedal of an accelerator — is completely closed. Otherwise the drive is necessary for adjusting.
3. Take from a cut of a tip of a cover of a cable spring скобу and tip moving to an aperture rubber демпфера forward achieve, that throttle заслонка it was completely closed. At not completely opening заслонке moving achieve back, that заслонка completely opened. Fix a cable tip in new position, having inserted скобу into its corresponding cut.
    
THE NOTE
If the cable is adjusted correctly, the deflection from effort of a hand of its branch between a tip of a cover and sector of throttle knot should be no more than 10 mm.

4. If a cable greatest possible will pull moving of a tip of a cover in демпфере, and throttle заслонка all the same completely does not open, increase a full speed of a pedal of an accelerator the persistent screw established on a pedal under the panel of devices. At a reversing of the screw from a pedal arm its course increases, at вворачивании — decreases.
5. For cable replacement take out a tip of a cable of a drive throttle заслонки from a groove of sector and disconnect a cable from throttle knot.
6. Deduce демпфер covers of a cable from an arm cut.
7. In salon under the panel of devices compress a screw-driver цанговый a clip of a tip of a cable, take it from an aperture of a pedal and deduce a cable from a cut in a pedal.
8. Extend a cable in подкапотное space through an aperture in a board передка.
9. Establish a cable of a drive throttle заслонки in an order, the return to removal.
10. After installation adjust a cable tension (subitem 1-4 of this subsection see).

«The previous page
5.14.11. Check and replacement of a regulator of idling
The following page»
5.14.13. Removal and installation of a pedal of an accelerator











cf8e4909