Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
5.1. Features of a design
5.2. Compression check in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in position ВМТ of a step of compression
5.6. Removal, installation and дефектовка a flywheel
5.7. Replacement of details of consolidation of the engine
5.8. A head of the block of cylinders
5.9. Removal and engine installation
5.10. Engine repair
5.11. Greasing system
5.12. Cooling system
5.13. System of release of the fulfilled gases
5.14. The engine power supply system
5.14.1. Features of a design
5.14.2. Pressure check in the engine power supply system
5.14.3. Pressure decrease in the power supply system
5.14.4. Removal and installation of the air filter, the muffler of noise of an admission and an air line
5.14.5. Replacement of the fuel pump
5.14.6. Replacement of a fuel tank and its bulk pipe
5.14.7. Check and replacement of a regulator of pressure of fuel
5.14.8. Removal and installation of a fuel stage
5.14.9. Removal, installation and check of atomizers
5.14.10. Removal and installation of throttle knot
5.14.11. Check and replacement of a regulator of idling
5.14.12. Adjustment and replacement of a cable of a drive throttle заслонки
5.14.13. Removal and installation of a pedal of an accelerator
5.15. System of catching of steams of fuel
5.16. System рециркуляции the fulfilled gases
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 








5-14-13-snyatie-i-ustanovka-pedali-akseleratora.html

5.14.13. Removal and installation of a pedal of an accelerator

Accelerator pedal remove for replacement of plastic plugs of its axis at occurrence of a scratch, jamming or increased люфте, and also for replacement of a returnable spring at its damage.

THE NOTE
And its returnable spring it is possible to replace plugs of an axis of a pedal of an accelerator and it is direct on the car but as access to a pedal is complicated enough, we recommend to remove a pedal in gathering with an arm.

It be required to you: a face key «on 12», a screw-driver.
1. Disconnect from a pedal a cable of a drive throttle заслонки (Adjustment and replacement of a cable of a drive throttle заслонки »see«).
2. Turn on two nuts of fastening of an arm of a pedal to a board передка
3. … also remove an accelerator pedal in gathering with an arm.

Fig. 5.26. An accelerator pedal: 1 – a pedal platform; 2 – a pedal core; 3 – a pedal arm; 4 – a washer; 5 – a pedal axis; 6 – a lock washer; 7 – the plug; 8 – a returnable spring

4. For replacement of two plastic plugs 7 (fig. 5.26) axes of 5 pedals remove from both ends of an axis lock washers 6, having hooked their screw-driver. Then take an axis 5 of apertures of an arm 3, serially removing from it the plastic plug 7, a steel washer 4 and a returnable spring 8. Remove from an axis the second steel washer and the plastic plug.
    
THE NOTE
So details of fastening of a pedal of an accelerator look. In a photo they are located in the same order in which are established on the car.

5. Collect a pedal of an accelerator and establish it on the car in an order, the return to dismantling and removal.

«The previous page
5.14.12. Adjustment and replacement of a cable of a drive throttle заслонки
The following page»
5.15. System of catching of steams of fuel











cf8e4909