Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
5.1. Features of a design
5.2. Compression check in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in position ВМТ of a step of compression
5.6. Removal, installation and дефектовка a flywheel
5.7. Replacement of details of consolidation of the engine
5.8. A head of the block of cylinders
5.9. Removal and engine installation
5.10. Engine repair
5.11. Greasing system
5.12. Cooling system
5.13. System of release of the fulfilled gases
5.14. The engine power supply system
5.14.1. Features of a design
5.14.2. Pressure check in the engine power supply system
5.14.3. Pressure decrease in the power supply system
5.14.4. Removal and installation of the air filter, the muffler of noise of an admission and an air line
5.14.5. Replacement of the fuel pump
5.14.6. Replacement of a fuel tank and its bulk pipe
5.14.7. Check and replacement of a regulator of pressure of fuel
5.14.8. Removal and installation of a fuel stage
5.14.9. Removal, installation and check of atomizers
5.14.10. Removal and installation of throttle knot
5.14.11. Check and replacement of a regulator of idling
5.14.12. Adjustment and replacement of a cable of a drive throttle заслонки
5.14.13. Removal and installation of a pedal of an accelerator
5.15. System of catching of steams of fuel
5.16. System рециркуляции the fulfilled gases
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 



cf8e4909





5-14-3-snizhenie-davleniya-v-sisteme-pitaniya.html

5.14.3. Pressure decrease in the power supply system

THE PREVENTION
Fuel is in the power supply system under a high pressure, therefore it is forbidden to weaken connections топливопроводов in an operating time of the engine or right after its stop. For work on power supply system repair on just stopped engine it is necessary to lower preliminary pressure in the power supply system. Through 2–3 ч after a stop of the engine pressure in the power supply system will fall practically to zero.

1. Switch off ignition, open a cowl and establish it on an emphasis.

Fig. 10.2. Numbers of safety locks, fusible inserts and the relay in the assembly block located in подкапотном space of car Chevrolet Lanos

Fig. 10.3. Numbers of safety locks, fusible inserts and the relay in the assembly block located in подкапотном space of car Daewoo Lanos

2. Disconnect a wire from the plug "minus" of the storage battery.
3. Uncover the assembly block of safety locks and the relay, located in подкапотном space (the Arrangement of safety locks, fusible inserts and the relay and their replacement see).
4. Take from the assembly block of the relay №30 (fig. 10.2 see) fuel pump. On car Daewoo Lanos take from the assembly block of the relay № 31 (fig. 10.3 see)
5. Connect a wire to the plug "minus" of the storage battery, start up the engine and allow to it to work before full development of fuel from a fuel stage. After that the engine will decay.
6. Switch off ignition. Now it is possible to separate топливопроводы.

The previous page
5.14.2. Pressure check in the engine power supply system
The following page
5.14.4. Removal and installation of the air filter, the muffler of noise of an admission and an air line