Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
5.1. Features of a design
5.2. Compression check in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in position ВМТ of a step of compression
5.6. Removal, installation and дефектовка a flywheel
5.7. Replacement of details of consolidation of the engine
5.8. A head of the block of cylinders
5.9. Removal and engine installation
5.10. Engine repair
5.11. Greasing system
5.12. Cooling system
5.13. System of release of the fulfilled gases
5.14. The engine power supply system
5.15. System of catching of steams of fuel
5.16. System рециркуляции the fulfilled gases
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 








5-4-zamena-opor-podveski-silovogo-agregata.html

5.4. Replacement of support of a suspension bracket of the power unit

The power unit is established on two support with rubber pillows on the right and at the left and one support (too with a rubber pillow), fixed through an arm on картере transmissions.
It be required to you: a face head «on 14», keys «on 17», «on 19», a jack or the similar load-lifting mechanism.
1. Will hang out a forward part of the car on support or lift the car on the lift.
2. Remove the right mudguard of the engine (Removal and installation of mudguards of the engine »see«).

THE NOTE
For replacement of the right support of a suspension bracket of the power unit it is enough to remove only the right mudguard. For replacement of the left forward and back support it is not necessary to remove mudguards.

3. Establish under картер the engine a jack or a support.
4. For replacement of a back support of a suspension bracket of the power unit turn away a nut of a bolt of fastening of a support to an arm on a transmission...
5. … also turn out two bolts of fastening of a support to a body.

THE NOTE
Forward bolt of fastening of a support turn out through an aperture in an arm.

6. Lower a support under the engine so that the support of a suspension bracket of the power unit was released, then take out a bolt of fastening of a support and remove it.
7. Establish a back support of a suspension bracket of the power unit in an order, the return to removal, сориентировав at installation so that an arrow put on its external surface, has been directed forward in a direction of movement of the car.

THE NOTE
Back and left support of a suspension bracket of the power unit of almost identical form also differ only with quantity of apertures in an internal holder, therefore pay attention to support marks. Get a new support with the same designation.

8. For replacement of the left support of a suspension bracket of the power unit turn out on two bolts of fastening of a support to an arm …
9. … and to a body longeron …
10. … also remove a support.

THE NOTE
Pay attention to support marks. Get a new support with the same designation.

11. Establish the left support of a suspension bracket of the power unit in an order, the return to removal.
12. Before replacement of the right support of a suspension bracket of the power unit remove a belt of a drive of the compressor of the conditioner («Replacement of a belt of a drive of the compressor of the conditioner» see) as it complicates access to a pillow.
13. Turn on two nuts of fastening of the right support to a body arm …
14. … turn out two bolts of fastening of a support to an engine arm …
15. … also remove a support.
16. Establish the right support of a suspension bracket of the power unit and all removed details in an order, the return to removal.

«The previous page
5.3. Removal and installation of mudguards of the engine
The following page»
5.5. Installation of the piston of the first cylinder in position ВМТ of a step of compression











cf8e4909