Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
6. Transmission
6.1. Coupling
6.2. A transmission
6.2.1. Features of a design
6.2.2. Possible malfunctions of a transmission, their reason and ways of elimination
6.2.3. Oil replacement in a transmission
6.2.4. Replacement of epiploons of a transmission
6.2.5. Removal and transmission installation
6.2.6. Dismantling and assemblage of a transmission and дефектовка its details
6.2.7. Repair of a secondary shaft
6.2.8. Repair of a primary shaft
6.2.9. Synchronizer repair
6.2.10. Differential repair
6.2.11. Repair of the mechanism of a gear change
6.2.12. Repair of hinges of a drive of a gear change
6.2.13. Removal, installation and repair of a side scene of a control lever by a transmission
6.2.14. Adjustment of a drive of management by a transmission
6.3. Drives of forward wheels
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 



cf8e4909





6-2-5-snyatie-i-ustanovka-korobki-peredach.html

6.2.5. Removal and transmission installation

It be required to you: keys on 12, on 14, on 19.
2. If a transmission remove for repair, merge from it oil (oil Replacement in a transmission see).
3. Disconnect drives of forward wheels from a transmission (Removal and installation of drives of forward wheels see).
4. Mark in any way (for example, a paint) a relative positioning of draught and a tip of the lever of a gear change to keep drive adjustment at return installation of a box.
5. Loosen the a bolt inhaling клеммового a clip of a drive of management of the gear change mechanism...
6. … also separate draught and a tip of the lever of a gear change.
7. Disconnect колодки a motor plait of wires from the gauge of speed …
8. … and from the switch of light of a backing.
9. Turn on two nuts of bolts of fastening of an arm of the working cylinder of coupling, keeping the bottom bolt from проворачивания the second key.
10. Take aside the working cylinder of coupling in gathering with an arm and a hose.
11. Establish a support under oil картер the engine, using a piece of a board as the prorate.
12. Establish a support under a transmission and turn out three bolts of fastening of an arm of the left forward support of a suspension bracket of the power unit to a transmission.
13. Turn out two bolts of fastening of a support to a body longeron (Replacement of support of a suspension bracket of the power unit see) and remove a support in gathering with an arm.
14. Turn out two bolts of fastening of a box to the block of cylinders under a water distributive pipe …
15. … a bolt located near the oil filter …
16. … and four bolts (on a turn-key basis on 14) fastenings oil картера to картеру transmissions.
17. Turn out fastening bolts картера transmissions to the block of cylinders of the engine, nearby with a starter …
18. … and near to an eye картера transmissions for fastening of an arm of the working cylinder of coupling.
19. Turn out two bolts of fastening of a back support of the power unit to a body (Replacement of support of a suspension bracket of the power unit see) …
20. … also remove a transmission from the car together with a back support of a suspension bracket of the power unit.

THE PREVENTION
Not опирайте the end of a primary shaft on petals of a press spring of coupling not to deform them.

21. Establish a transmission in an order, the return to removal.

GOOD ADVICE
Before transmission installation apply a thin film консистентной greasings on шлицевую a part of a primary shaft.

22. Fill in oil in a transmission (oil Replacement in a transmission see, with. 139) if it merged before box removal.
23. Adjust a drive of management of the gear change mechanism (Adjustment of a drive of management by a transmission see).

The previous page
6.2.4. Replacement of epiploons of a transmission
The following page
6.2.6. Dismantling and assemblage of a transmission and дефектовка its details