Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
6. Transmission
6.1. Coupling
6.2. A transmission
6.2.1. Features of a design
6.2.2. Possible malfunctions of a transmission, their reason and ways of elimination
6.2.3. Oil replacement in a transmission
6.2.4. Replacement of epiploons of a transmission
6.2.5. Removal and transmission installation
6.2.6. Dismantling and assemblage of a transmission and дефектовка its details
6.2.7. Repair of a secondary shaft
6.2.8. Repair of a primary shaft
6.2.9. Synchronizer repair
6.2.10. Differential repair
6.2.11. Repair of the mechanism of a gear change
6.2.12. Repair of hinges of a drive of a gear change
6.2.13. Removal, installation and repair of a side scene of a control lever by a transmission
6.2.14. Adjustment of a drive of management by a transmission
6.3. Drives of forward wheels
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 








6-2-13-snyatie-ustanovka-i-remont-kulisy-rychaga-upravleniya-korobkojj-peredach.html

6.2.13. Removal, installation and repair of a side scene of a control lever by a transmission

If after repair or replacement of a drive of a gear change vibration of the lever of a gear change at movement remains, means, is available raised люфт in hinges of the lever and they are necessary for repairing.
It be required to you: keys «on 12», «on 14», a face key «on 10», a screw-driver.
1. In a motor compartment ослабьте a bolt nut клеммового connections of a tip of the lever and draught of a gear change.
2. Remove from draught coupling муфту
3. … and a protective cover.
4. In salon take from a forward part of facing of a tunnel of a floor a framework of a cover of a control lever a transmission, overcoming effort of its clamps.
5. Turn a lever cover inside out, have a bite бокорезами (or knife) a collar of fastening of a cover and remove a cover from the lever.

    
THE NOTE
Collar of fastening of a cover of the lever of a gear change of disposable use. At assemblage establish a new collar.

6. Remove a forward part of facing of a tunnel of a floor (Removal and installation of facing of a tunnel of a floor »see«).
7. Unfasten from the lever an axis clamp …
8. … also remove a lever axis, taking it from lever and side scene apertures.
9. Having pulled upwards, remove the gear change lever.
10. Push a screw-driver in the lever case резинопластмассовую directing plug and advance it lengthways on a shaft.
11. Turn out four bolts of fastening of the case of the lever to the body basis.
12. Remove the case and take from it a shaft.
13. Remove from a shaft directing plug.
14. Examine the removed details. If the aperture of the directing plug is worn out or its rubber file is deformed or has hardened, replace the plug in gathering. If in side scene hinges is люфт or the aperture under a lever axis is worn strongly out, replace a side scene.
15. Establish details in sequence, return to removal.
16. Adjust a gear change drive («Adjustment of a drive of management by a transmission» see).

«The previous page
6.2.12. Repair of hinges of a drive of a gear change
The following page»
6.2.14. Adjustment of a drive of management by a transmission











cf8e4909