Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
6. Transmission
6.1. Coupling
6.2. A transmission
6.2.1. Features of a design
6.2.2. Possible malfunctions of a transmission, their reason and ways of elimination
6.2.3. Oil replacement in a transmission
6.2.4. Replacement of epiploons of a transmission
6.2.5. Removal and transmission installation
6.2.6. Dismantling and assemblage of a transmission and дефектовка its details
6.2.7. Repair of a secondary shaft
6.2.8. Repair of a primary shaft
6.2.9. Synchronizer repair
6.2.10. Differential repair
6.2.11. Repair of the mechanism of a gear change
6.2.12. Repair of hinges of a drive of a gear change
6.2.13. Removal, installation and repair of a side scene of a control lever by a transmission
6.2.14. Adjustment of a drive of management by a transmission
6.3. Drives of forward wheels
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 



cf8e4909





6-2-12-remont-sharnirov-privoda-pereklyucheniya-peredach.html

6.2.12. Repair of hinges of a drive of a gear change

Gear change drive:
1 – a tip of the lever of a gear change;
2 – the gear change lever;
3 – draught of a choice of transfers;
4 – the hinge of a shaft of a gear change;
5 – a gear change shaft;
6 – the hinge of the lever of a gear change

At increase in backlashes in a gear change drive there is a vibration of the lever of a gear change during movement, and the gear change becomes indistinct and complicated. In this case it is necessary to repair drive hinges.
The screw-driver is required to you.
1. For replacement of plugs of the hinge of the lever of a gear change wring out a screw-driver clamps of an axis of the lever …
2. … also take an axis from apertures of the hinge of the lever and an arm of a back support of the power unit. Take away the lever of a gear change from an arm.
3. Take two plastic plugs of the hinge from lever apertures.
4. Remove from each plastic plug rubber демпферные plugs …
5. … and sealing rings. The hardened or damaged rubber plugs and rings replace.
6. Collect the hinge of the lever of a gear change in sequence, return dismantling.
7. For repair of the hinge of a shaft of a gear change remove a spring clamp …
8. … also take an axis of the hinge of a drive of a gear change. Separate hinge plugs.
9. Take out from a shaft plug a plastic cracker.
10. Collect the hinge of draught of a gear change in sequence, return dismantling.
11. Draught of a choice of transfers is made in gathering with hinges, therefore at occurrence люфтов in draught hinges replace draught in gathering.
12. Wring out a plastic clamp of the hinge …
13. … also remove the hinge from a spherical finger of the lever of a gear change.
14. Similarly disconnect the second hinge and remove draught.
15. Establish draught of a choice of transfers to sequences, return to removal.

    
THE NOTE
If after repair of hinges of the lever and draught of a gear change, and also after replacement of draught of a choice of transfers in a drive has remained raised люфт, means, backlashes in other not folding hinges of a drive are increased. In this case replace a drive in gathering.

The previous page
6.2.11. Repair of the mechanism of a gear change
The following page
6.2.13. Removal, installation and repair of a side scene of a control lever by a transmission