Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
4.1. General provisions
4.2. Daily service (ЕО)
4.3. The first maintenance service (ТО-1)
4.3.1. Check and adjustment of a tension of a belt of a drive of the generator and the pump of the hydraulic booster of a steering
4.3.2. Check and adjustment of a tension of a belt of a drive of the compressor of the conditioner
4.3.3. Check of a belt of a drive газораспределительного the mechanism
4.3.4. Oil replacement in the engine and the oil filter
4.3.5. Clearing of system of ventilation картера
4.3.6. Check of hoses and connections of system of cooling
4.3.7. Check of system of release of the fulfilled gases
4.3.8. Tightness check топливопроводов
4.3.9. Replacement of the fuel filter
4.3.10. Replacement of a filtering element of the air filter
4.3.11. Check and adjustment of a drive of deenergizing of coupling
4.3.12. Check of level and доливка oils in a transmission
4.3.13. Check of protective covers of drives of forward wheels
4.3.14. Check of a technical condition of details of a forward suspension bracket on the car
4.3.15. Check of a technical condition of details of a back suspension bracket on the car
4.3.16. Check and adjustment of corners of installation of wheels
4.3.17. Survey and steering check on the car
4.3.18. Free wheeling check (люфта) a steering wheel
4.3.19. Check of tightness of a hydrodrive of brakes
4.3.20. Check of degree of deterioration brake колодок, disks and drums
4.3.21. Check of work of the vacuum amplifier of brakes
4.3.22. Check of an overall performance of brake system
4.3.23. Check of a lay brake
4.3.24. Service of the storage battery
4.3.25. Replacement and service of spark plugs
4.3.26. Check and adjustment of light of headlights
4.3.27. Greasing of armature of a body
4.3.28. Procleaning of drainage apertures
4.4. The second maintenance service (ТО-2)
5. The engine
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 








4-3-4-zamena-masla-v-dvigatele-i-maslyanogo-filtra.html

4.3.4. Oil replacement in the engine and the oil filter

According to the recommendation of manufacturer in the engine it is necessary to replace oil in one year of operation or through 10 thousand in km of run depending on that will come earlier.

GOOD ADVICE
Under trying conditions operation in a big city or strongly dusty district replace oil and the filter through each 5000 km.

It be required to you: engine oil, the oil filter, a pure rag, capacity for merged oil capacity not less than 5 l, a key «on 19», a special key for отворачивания the oil filter.

GOOD ADVICE
Oil merge after a trip while the engine has not cooled down yet. If the engine cold, start up and warm up it to working temperature.
Fill in oil of the same mark, as at oil which was in the engine. If all of you have decided to replace oil mark, wash out greasing system промывочным oil or oil of that mark which will be used. For this purpose after plum of old oil fill in new to the bottom label маслоизмерительного щупа. Start up the engine and allow to it to work 10 mines idling. Merge oil and only after that replace the oil filter. Now can fill in new oil to demanded level (to the top label on щупе).

THE PREVENTION
Do not merge the fulfilled oil on the earth.

1. Clear a metal brush, and then a rag a stopper of a drain aperture on oil картере the engine. Turn away a stopper of a drain aperture, preliminary having substituted capacity for merged oil …
2. … also merge oil.

    
THE PREVENTION
Be cautious: oil is hot.

3. Wrap a stopper.

THE NOTE
The stopper is condensed by a copper washer. If the washer is pressed strongly out, necessarily replace it.

4. Shift from a place a special key the oil filter …

THE NOTE
The oil filter is established on a forward part of the block of cylinders of the engine around 4th cylinder.

5. … also remove it.
6. Check up cleanliness and mobility противодренажного the valve.

GOOD ADVICE
For отворачивания the oil filter use a special key. If such key or a similar stripper is not present, punch the case of the filter a screw-driver and, using it as the lever, turn away the filter. Punch the filter as it is possible more close to a bottom not to damage the union. It is possible to take advantage and the strip of a rough emery paper curtailed twice, having wrapped up it the filter and having shifted it from a place hands.

7. If the sealing ring of the new filter is not processed by the manufacturer консистентной greasing or talc, grease a ring with pure engine oil and wrap the filter on a place (hands without tool application) on 3/4 turns from the moment of contact of a ring and a flange of the block of cylinders.
8. Turn away a stopper маслоналивной mouths …
9. … also remove it.
10. Fill in pure engine oil (Check of level and доливка oils in greasing system »see«). Establish into place a stopper маслоналивной mouths.
11. Start up the engine and allow to it to work idling some minutes (the alarm lamp of emergency pressure drop of oil should go out through 2–3 with the ambassador of start-up of the engine). In an engine operating time check up, whether is not present потеков some oil from under a stopper of a drain aperture and the oil filter. Stop the engine, check up oil level, if necessary add oil, tighten a stopper and the filter.

«The previous page
4.3.3. Check of a belt of a drive газораспределительного the mechanism
The following page»
4.3.5. Clearing of system of ventilation картера











cf8e4909