Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
4.1. General provisions
4.2. Daily service (ЕО)
4.3. The first maintenance service (ТО-1)
4.3.1. Check and adjustment of a tension of a belt of a drive of the generator and the pump of the hydraulic booster of a steering
4.3.2. Check and adjustment of a tension of a belt of a drive of the compressor of the conditioner
4.3.3. Check of a belt of a drive газораспределительного the mechanism
4.3.4. Oil replacement in the engine and the oil filter
4.3.5. Clearing of system of ventilation картера
4.3.6. Check of hoses and connections of system of cooling
4.3.7. Check of system of release of the fulfilled gases
4.3.8. Tightness check топливопроводов
4.3.9. Replacement of the fuel filter
4.3.10. Replacement of a filtering element of the air filter
4.3.11. Check and adjustment of a drive of deenergizing of coupling
4.3.12. Check of level and доливка oils in a transmission
4.3.13. Check of protective covers of drives of forward wheels
4.3.14. Check of a technical condition of details of a forward suspension bracket on the car
4.3.15. Check of a technical condition of details of a back suspension bracket on the car
4.3.16. Check and adjustment of corners of installation of wheels
4.3.17. Survey and steering check on the car
4.3.18. Free wheeling check (люфта) a steering wheel
4.3.19. Check of tightness of a hydrodrive of brakes
4.3.20. Check of degree of deterioration brake колодок, disks and drums
4.3.21. Check of work of the vacuum amplifier of brakes
4.3.22. Check of an overall performance of brake system
4.3.23. Check of a lay brake
4.3.24. Service of the storage battery
4.3.25. Replacement and service of spark plugs
4.3.26. Check and adjustment of light of headlights
4.3.27. Greasing of armature of a body
4.3.28. Procleaning of drainage apertures
4.4. The second maintenance service (ТО-2)
5. The engine
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 



cf8e4909





4-3-26-proverka-i-regulirovka-sveta-far.html

4.3.26. Check and adjustment of light of headlights

Check and adjustment of light of headlights spend on the equipped car (with completely filled fuel tank, the complete set of tools and a spare wheel).
The screw-driver with a crosswise edge is required to you.
1. Preliminary check up and if necessary finish to norm pressure of air in tyres.

Fig. 4.6. Adjustment of light of headlights

2. Establish the car to perpendicularly smooth wall (for example, in garage) on distance of 3 m. Put on a seat of the driver additional cargo in weight of 75 kg. Mark on a wall the screen, as is shown in fig. 4.6. The longitudinal plane of symmetry of the car should pass in the area of 0 on the screen. Rock the car sideways, that самоустановились springs of suspension brackets.
3. Measure on your car height of the centres of headlights from a floor. It will be distance h on the screen.
4. Establish a regulator of the electroproof-reader of light of headlights on the panel of devices in the position corresponding to loading of the car with one driver.
5. Include a passing light.
6. The direction of a light stain is recommended to be regulated for each headlight separately. The second headlight during adjustment close an opaque material.
7. Open a cowl and, rotating adjusting screws, adjust position on the screen of a light stain for each headlight across …
8. … and on a vertical if the arrangement of light stains does not correspond to drawing.
9. Headlights are considered adjusted, when the top borders of the left parts of light stains coincide with a line 4 (see fig. 4.6), and vertical lines 1 and 2 take place through points Е1 and Е2 crossings of horizontal and inclined sites of light stains.
If on the car antifog headlights the direction of their beam of light is necessary for adjusting only on height are established. Rotating the adjusting screw, achieve, that the top borders of light stains were on a line 4 or hardly below it.

The previous page
4.3.25. Replacement and service of spark plugs
The following page
4.3.27. Greasing of armature of a body