Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
5.1. Features of a design
5.2. Compression check in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in position ВМТ of a step of compression
5.6. Removal, installation and дефектовка a flywheel
5.7. Replacement of details of consolidation of the engine
5.8. A head of the block of cylinders
5.9. Removal and engine installation
5.10. Engine repair
5.11. Greasing system
5.12. Cooling system
5.12.1. Features of a design
5.12.2. Possible malfunctions of system of cooling, their reason and ways of elimination
5.12.3. Removal and installation of electrofans of a radiator of system of cooling of the engine
5.12.4. Replacement of a radiator of system of cooling
5.12.5. Replacement of the water pump
5.12.6. Removal and thermostat installation
5.12.7. Removal and installation of a broad tank
5.13. System of release of the fulfilled gases
5.14. The engine power supply system
5.15. System of catching of steams of fuel
5.16. System рециркуляции the fulfilled gases
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 



cf8e4909





5-12-5-zamena-vodyanogo-nasosa.html

5.12.5. Replacement of the water pump

The pump remove for repair or replacement at occurrence during its work of the noise which level exceeds usual, and leaks of a cooling liquid.
Pump dismantling labour-consuming enough, therefore we recommend to replace at malfunction the pump in gathering.
The key-shestigrannik on 5 is required to you.
1. Merge a liquid from cooling system (Replacement of a cooling liquid see).
2. Remove a drive belt газораспределительного the mechanism and a tension roller (Replacement and adjustment of a tension of a belt of a drive газораспределительного the mechanism see and replacement of its tension roller), the bottom and back covers of a drive газораспределительного the mechanism (Removal and installation of the oil pump see).
3. Turn out three screws of fastening of the pump to the block of cylinders and remove the pump together with a rubber sealing ring.

    
GOOD ADVICE
At each removal of the water pump it is recommended to replace screws of its fastening new as they are subject to oxidation and after long operation can break off at a reversing. Besides, a nest in a screw head under шестигранник rather small and its sides at a screw reversing are rumpled. At an inhaling and a repeated reversing of the screw its damaged sides can be crumpled absolutely, and will turn out the screw very inconveniently. For the prevention of "souring" of screws grease their carving анаэробным with a carving clamp.

4. Remove a sealing ring from the pump case.

    
GOOD ADVICE
We recommend to replace at each removal of the pump a sealing ring new.
Before installation of the pump for hermetic sealing of connection and prevention of sticking of a sealing ring grease a ring with technical vaseline.

5. Establish the pump in a nest of the block of cylinders, сориентировав its case проточкой (it is shown by arrows) at a case end face upwards, and fix screws.
6. Establish details in an order, the return to removal.
7. Adjust a tension of a belt of a drive газораспределительного the mechanism (Replacement and adjustment of a tension of a belt of a drive газораспределительного the mechanism and replacement of its tension roller see.
8. Fill in cooling liquid (Replacement of a cooling liquid see).

The previous page
5.12.4. Replacement of a radiator of system of cooling
The following page
5.12.6. Removal and thermostat installation