Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
5.1. Features of a design
5.2. Compression check in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in position ВМТ of a step of compression
5.6. Removal, installation and дефектовка a flywheel
5.7. Replacement of details of consolidation of the engine
5.8. A head of the block of cylinders
5.9. Removal and engine installation
5.10. Engine repair
5.11. Greasing system
5.11.1. Features of a design
5.11.2. Removal and installation of the oil pump
5.11.3. Repair of the oil pump
5.12. Cooling system
5.13. System of release of the fulfilled gases
5.14. The engine power supply system
5.15. System of catching of steams of fuel
5.16. System рециркуляции the fulfilled gases
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 








5-11-2-snyatie-i-ustanovka-maslyanogo-nasosa.html

5.11.2. Removal and installation of the oil pump

The oil pump remove for repair at decrease in its giving causing constant pressure drop of oil in system of greasing of the engine, and also at an oil leak through a sealing lining.
It be required to you: all tools necessary for removal of a belt of a drive газораспределительного of the mechanism and oil картера of the engine, and also a key «on 10».
1. Disconnect a wire from the plug "minus" of the storage battery.
3. Establish the piston of 1st cylinder in position ВМТ of a step of compression (Installation of the piston of the first cylinder in position ВМТ of a step of compression »see«).
4. Turn out a bolt of fastening and take out from an aperture in the case of the oil pump the gauge of position of a cranked shaft (Check and replacement of gauges of a control system with the engine »see«).
5. Remove a drive belt газораспределительного the mechanism and a tension roller (Replacement and adjustment of a tension of a belt of a drive газораспределительного the mechanism and replacement of its tension roller »see«).

THE PREVENTION
After removal of a belt of a drive газораспределительного the mechanism it is forbidden to turn distributive and cranked shaft as pistons can damage valves.

6. Remove a gear pulley of a camshaft («Replacement of an epiploon of a camshaft» see).
7. Turn out two top bolts of fastening of a back cover of a drive газораспределительного the mechanism …
8. … two bottom bolts …
9. … also uncover.
10. Remove oil картер the engine (Replacement of consolidation oil картера »see«).
11. Turn out a bolt скобы tube fastenings маслоприемника to the block of cylinders …
12. … two bolts of fastening маслоприемника to the oil pump …
13. … also remove маслоприемник.
14. The flange маслоприемника is condensed by a rubber ring. Strongly pressed out, hardened or torn ring necessarily replace, otherwise because of негерметичности connections giving of the oil pump can sharply decrease.

GOOD ADVICE
At each removal маслоприемника necessarily wash out its grid gasoline or kerosene to remove varnish adjournment from oil.

15. Remove a gear pulley of a cranked shaft.
16. Turn out seven bolts of fastening of the oil pump to the block of cylinders.
17. Having hooked the pump two screw-drivers, remove it from adjusting plugs in the block of cylinders.
18. If the lining of the case of the pump remained on the block of cylinders, separate its sharp tool and remove.
GOOD ADVICE
At each removal of the oil pump replace a lining new. Establish only a firm lining of factory manufacturing as the lining of other thickness will cause infringement of normal work of the pump.
Also at each removal of the pump replace a forward epiploon of a cranked shaft («Repair of the oil pump» see).

19. Clear привалочные surfaces of the block of cylinders and the case of the pump of the rests of an old lining.
20. Before installation fill a cavity of the oil pump консистентной with greasing for maintenance всасывания oils from oil картера at the first start-up of the engine.
21. Establish the pump in an order, the return to removal, and tighten bolts of its fastening in regular intervals cross-wise the moment 7 Н·м (0,7 кгс·м).
22. Establish the removed details and fill in oil in the engine (oil Replacement in the engine and the oil filter »see«).

GOOD ADVICE
At installation of the new or repaired oil pump it is recommended to replace the oil filter.

«The previous page
5.11.1. Features of a design
The following page»
5.11.3. Repair of the oil pump











cf8e4909