Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
5.1. Features of a design
5.2. Compression check in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in position ВМТ of a step of compression
5.6. Removal, installation and дефектовка a flywheel
5.7. Replacement of details of consolidation of the engine
5.7.1. Replacement of a lining of a cover of a head of the block of cylinders
5.7.2. Replacement of a lining of a head of the block of cylinders
5.7.3. Replacement маслосъемных caps
5.7.4. Replacement of an epiploon of a camshaft
5.7.5. Replacement of epiploons of a cranked shaft
5.7.6. Replacement of consolidation oil картера
5.7.7. Replacement of a lining of an inlet pipe
5.7.8. Replacement of a lining of a final collector
5.8. A head of the block of cylinders
5.9. Removal and engine installation
5.10. Engine repair
5.11. Greasing system
5.12. Cooling system
5.13. System of release of the fulfilled gases
5.14. The engine power supply system
5.15. System of catching of steams of fuel
5.16. System рециркуляции the fulfilled gases
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 








5-7-4-zamena-salnika-raspredelitelnogo-vala.html

5.7.4. Replacement of an epiploon of a camshaft

At detection of traces подтекания oils through a camshaft epiploon at first check up, whether the ventilation system картера is littered and whether hoses of system of ventilation картера are pressed, if necessary eliminate malfunctions. If the oil leak does not stop, replace an epiploon.
It be required to you: all tools necessary for removal of a drive газораспределительного of the mechanism (Replacement and adjustment of a tension of a belt of a drive газораспределительного the mechanism and replacement of its tension roller »see«), and also a key «on 17», a screw-driver, пассатижи, a hammer.
1. Disconnect a wire from the plug "minus" of the storage battery.
2. Establish the piston of 1st cylinder in position ВМТ of a step of compression (Installation of the piston of the first cylinder in position ВМТ of a step of compression »see«).
3. Remove a drive belt газораспределительного the mechanism (Replacement and adjustment of a tension of a belt of a drive газораспределительного the mechanism and replacement of its tension roller »see«).
4. Turn out a bolt of fastening of a gear pulley of a camshaft, keeping a pulley from проворачивания, as is shown in a photo, inserted into apertures of a pulley handles пассатижей and the big screw-driver …
5. … also remove a pulley.
6. Having hooked a screw-driver, take an epiploon from a nest of the forward bearing of a camshaft.
7. Before installation of a new epiploon examine its working edge. It should be equal, without вырывов, dents and rubber flows. The epiploon spring should be whole and unextended. Grease a working edge with engine oil.

    
GOOD ADVICE
For simplification запрессовки an epiploon make on its landing edge a small facet with the help надфиля or small наждачного a circle.

8. Establish an epiploon a working edge in a bearing nest, accurately fill a working edge on a camshaft (for example, by means of a wooden stick) and запрессуйте against the stop by means of approaching send. In quality send it is possible to use an old epiploon.
9. Establish all removed details and knots in an order, the return to removal.
10. Adjust a tension of belts of a drive of the generator and the pump of the hydraulic booster of a steering (Check and adjustment of a tension of a belt of a drive of the generator and the pump of the hydraulic booster of a steering »see«), and also the conditioner compressor (Check and adjustment of a tension of a belt of a drive of the compressor of the conditioner »see«).

«The previous page
5.7.3. Replacement маслосъемных caps
The following page»
5.7.5. Replacement of epiploons of a cranked shaft











cf8e4909