Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
5.1. Features of a design
5.2. Compression check in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in position ВМТ of a step of compression
5.6. Removal, installation and дефектовка a flywheel
5.7. Replacement of details of consolidation of the engine
5.7.1. Replacement of a lining of a cover of a head of the block of cylinders
5.7.2. Replacement of a lining of a head of the block of cylinders
5.7.3. Replacement маслосъемных caps
5.7.4. Replacement of an epiploon of a camshaft
5.7.5. Replacement of epiploons of a cranked shaft
5.7.6. Replacement of consolidation oil картера
5.7.7. Replacement of a lining of an inlet pipe
5.7.8. Replacement of a lining of a final collector
5.8. A head of the block of cylinders
5.9. Removal and engine installation
5.10. Engine repair
5.11. Greasing system
5.12. Cooling system
5.13. System of release of the fulfilled gases
5.14. The engine power supply system
5.15. System of catching of steams of fuel
5.16. System рециркуляции the fulfilled gases
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 








5-7-8-zamena-prokladki-vypusknogo-kollektora.html

5.7.8. Replacement of a lining of a final collector

Between flanges of a head of the block of cylinders and a final collector the sealing lining made of pressed asbestine sheet, reinforced by a steel is established. At infringement of tightness of this lining there is a break outside of the fulfilled gases, accompanied by a characteristic sharp sound (a collector «сечет»). If it is not possible to eliminate malfunction a tightening of fastening of a final collector, replace a lining.
The face head «on 12» is required to you.

THE NOTE
At replacement of a lining of a final collector it is possible not to disconnect a flange of a reception pipe from a collector. There is enough, having turned away a nut of fastening of a collector, to remove it from hairpins of a head of the block and to take away from a head so, flexibility of system of release how much allows. Through the formed backlash it is possible to take out a collector lining.

Fig. 5.6. Sequence отворачивания nuts of fastening of a final collector


1. Remove the thermoscreen of a final collector (Removal and installation of thermoscreens »see«).
2. Turn away eight nuts of fastening of a final collector in the sequence shown on fig. 5.6.
3. Remove from hairpins a final collector …
4. … and the lining established under it.
5. Carefully clear привалочные surfaces of a head of the block and a final collector of the rests of an old lining and a deposit.
6. Establish a new lining and all removed details in sequence, return to removal.
7. Nuts of fastening of a final collector tighten in sequence, return shown on fig. 5.6, the moment resulted in the appendix 1.

GOOD ADVICE
In order to avoid burning of a lining and for increase of its tightness it is recommended to grease before lining installation it from both parties a thin layer of graphitic greasing.
Hairpins of a head of the block of cylinders grease with graphitic greasing.


«The previous page
5.7.7. Replacement of a lining of an inlet pipe
The following page»
5.8. A head of the block of cylinders











cf8e4909