Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
5.1. Features of a design
5.2. Compression check in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in position ВМТ of a step of compression
5.6. Removal, installation and дефектовка a flywheel
5.7. Replacement of details of consolidation of the engine
5.7.1. Replacement of a lining of a cover of a head of the block of cylinders
5.7.2. Replacement of a lining of a head of the block of cylinders
5.7.3. Replacement маслосъемных caps
5.7.4. Replacement of an epiploon of a camshaft
5.7.5. Replacement of epiploons of a cranked shaft
5.7.6. Replacement of consolidation oil картера
5.7.7. Replacement of a lining of an inlet pipe
5.7.8. Replacement of a lining of a final collector
5.8. A head of the block of cylinders
5.9. Removal and engine installation
5.10. Engine repair
5.11. Greasing system
5.12. Cooling system
5.13. System of release of the fulfilled gases
5.14. The engine power supply system
5.15. System of catching of steams of fuel
5.16. System рециркуляции the fulfilled gases
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 








5-7-7-zamena-prokladki-vpusknojj-truby.html

5.7.7. Replacement of a lining of an inlet pipe

Between flanges of a head of the block of cylinders and an inlet pipe the sealing lining made of pressed asbestine sheet, reinforced by a steel is established. At infringement of tightness of this lining the engine works roughly («троит»). If it is not possible to eliminate malfunction a tightening of fastening of an inlet pipe, replace a lining.
For replacement of a lining of an inlet pipe to disconnect any hoses (except a hose of system of ventilation картера the engine) and wires it is not required. Their flexibility allows to take away an inlet pipe from a head of the block of cylinders on distance, sufficient for lining removal.
It is required to you face or накидной a key «on 12».
1. Merge a liquid from cooling system («Replacement of a cooling liquid» see).
2. Loosen the a tension of a belt of a drive of the generator and the pump of the hydraulic booster of a steering also remove a belt from a generator pulley (Replacement of a belt of a drive of the generator and the pump of the hydraulic booster of a steering »see«).

Fig. 5.5. Sequence отворачивания nuts and bolts of fastening of an inlet pipe

3. Turn out a bolt of fastening of a tension lath of the generator and take away the generator from the engine, having turned it on an arm.
4. Loosen the a collar of fastening of a hose of system of ventilation картера the engine to a branch pipe of a cover of a head of the block of cylinders, having compressed пассатижами its unbent ears, shift a collar on a hose …
5. … also disconnect a hose from a cover.
6. Turn away ten nuts and bolts of fastening of an inlet pipe in the sequence shown on fig. 5.5.
7. Remove an inlet pipe from hairpins, take hardly aside and remove from hairpins a lining.
8. Carefully clear привалочные surfaces of a head of the block and an inlet pipe of the rests of an old lining.
9. Establish a new lining and all removed details in sequence, return to removal.
10. Bolts and nuts of fastening of an inlet pipe tighten in sequence, return shown on fig. 5.5, the moment resulted in the appendix 1.

    
GOOD ADVICE
In order to avoid sticking of a lining and for increase of its tightness it is recommended to grease before lining installation it from both parties a thin layer of graphitic greasing.
Hairpins of a head of the block of cylinders and bolts of fastening of an inlet pipe grease with graphitic greasing.


«The previous page
5.7.6. Replacement of consolidation oil картера
The following page»
5.7.8. Replacement of a lining of a final collector











cf8e4909