Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
6. Transmission
7. A running gear
7.1. A forward suspension bracket
7.2. A back suspension bracket
7.2.1. Features of a design
7.2.2. Possible malfunctions of a back suspension bracket, their reason and ways of elimination
7.2.3. Replacement of the shock-absorber of a back suspension bracket
7.2.4. Replacement of a spring of a back suspension bracket
7.2.5. Replacement сайлентблоков levers of a back suspension bracket
7.2.6. Adjustment of bearings of a back nave
7.2.7. Replacement of bearings of a back nave
7.2.8. Replacement of a beam of a back suspension bracket
7.2.9. Replacement of the stabilizer of cross-section stability of a back suspension bracket
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 








7-2-8-zamena-balki-zadnejj-podveski.html

7.2.8. Replacement of a beam of a back suspension bracket

The beam of a back suspension bracket is more convenient for removing on the lift. If there is no possibility to establish the car on the lift, lift a back part of the car, having established a jack under a beam. Then establish support under nests for jack installation on a car body.

GOOD ADVICE
To remove a beam of a back suspension bracket it is necessary with assistants who will hold and lower a beam of a back suspension bracket.
    
THE PREVENTION
Weaken and tighten bolts of fastening of a wheel only on the car standing on the earth. The moment of an inhaling of bolts 90 Н·м.

It be required to you: keys «on 10», «on 15», «on 17», «on 19» (two), a special key «on 10» for отворачивания nuts of brake pipelines, круглогубцы.
1. Remove back wheels.
2. Disconnect on one brake hose from both parties from pipelines on a beam of a back suspension bracket («Replacement of brake hoses» see) and muffle apertures of hoses.
3. Turn on from both parties on four nuts of fastening of pins …
4. … also remove pins in gathering with brake drums.
5. Turn away a nut of fastening of the pipeline to the working brake cylinder («Replacement of the working brake cylinder of the brake mechanism of a back wheel» see) …
6. … remove скобу fastenings of a cable of a lay brake to a brake board …
7. … disconnect a tip of a cable from разжимного the lever …
8. … also remove a board of a back brake in gathering.
9. Similarly remove a board of a back brake from a car opposite side.
10. Turn away a fastening nut …
11. … also disconnect the holder of a cable of a drive of a lay brake from the lever of a back suspension bracket.
12. Similarly disconnect the second branch of a cable from a car opposite side.
13. Turn out and take bolts of the bottom fastenings of shock-absorbers.
14. Smoothly lower a beam and remove springs of a back suspension bracket both their top and bottom linings («Replacement of a spring of a back suspension bracket» see).
15. Having released clamps, remove brake pipelines from a beam («Replacement of brake tubes» see).
16. Deduce brake hoses from beam arms, having removed preliminary скобы fastenings («Replacement of brake hoses» see).
17. Turn away a nut of bolts of fastening of a beam to a body, keeping bolts from проворачивания the second key; take bolts …
18. … also remove a beam in gathering with the stabilizer of cross-section stability.
19. If necessary remove the stabilizer to similarly its removal on the car («Replacement of the stabilizer of cross-section stability of a back suspension bracket» see) and выпрессуйте сайлентблоки (Replacement сайлентблоков levers of a back suspension bracket »see«).
20. Establish a beam of a back suspension bracket in an order, the return to removal. Definitively tighten nuts of bolts of fastening of a beam on the car standing on the earth.
21. After beam installation pump over brake system («Prorolling of a hydrodrive of brake system» see) and if necessary adjust a lay brake («Adjustment of a drive of a lay brake» see).

«The previous page
7.2.7. Replacement of bearings of a back nave
The following page»
7.2.9. Replacement of the stabilizer of cross-section stability of a back suspension bracket











cf8e4909