Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
6. Transmission
7. A running gear
8. A steering
9. Brake system
9.1. Features of a design
9.2. Possible malfunctions of brake system, their reason and ways of elimination
9.3. Prorolling of a hydrodrive of brake system
9.4. Check and adjustment of position of a pedal of a brake
9.5. The main brake cylinder
9.6. The vacuum amplifier of brakes
9.7. Replacement of hoses and tubes of a hydrodrive of brakes
9.8. Removal and installation of a pedal of a brake
9.9. Brake mechanisms of forward wheels
9.9.1. Replacement brake колодок the brake mechanism of a forward wheel
9.9.2. Replacement of a support of the forward brake mechanism
9.9.3. Replacement of a brake disk
9.10. Brake mechanisms of back wheels
9.11. A lay brake
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 



cf8e4909





9-9-1-zamena-tormoznykh-kolodok-tormoznogo-mekhanizma-perednego-kolesa.html

9.9.1. Replacement brake колодок the brake mechanism of a forward wheel

Check a condition brake колодок at each maintenance service.
Brake колодки replacement at deterioration of overlays (is minimum admissible thickness of frictional overlays of 1,5 mm), fragile connection of overlays with the basis, замасливании demand working surfaces, in the presence of deep furrows or having chopped off.

PREVENTIONS
Replace brake колодки forward brake mechanisms only with the complete set – 4 pieces (on two with each party).
Before replacement brake колодок check up level of a brake liquid in a tank of the main brake cylinder. If level is close to a label MAX, it is necessary to pump out a liquid part (for example, a medical syringe or a rubber pear) as after replacement worn out колодок new level will rise.

It be required to you: a key on 14, a key for bolts of wheels, sliding пассатижи.
1. Remove the left forward wheel.
2. Turn out the bottom bolt of fastening of a support …
3. … also lift a support upwards.
4. Remove brake колодки from the directing.

    
THE NOTE
Pay attention to marks brake колодок. New колодки get with the same marks.

5. Examine fixing springs колодок
6. … strongly deformed or корродированные springs replace.
7. Drown the piston of the working cylinder by means of sliding пассатижей.

GOOD ADVICE
At each replacement brake колодок without fail check a condition of protective rubber covers of directing fingers and character of moving of a support concerning directing brake колодок. If moving is complicated, grease консистентной with greasing directing fingers of a support. For this purpose …
… take directing finger …
… grease it консистентной with greasing and put greasing in an internal cavity of a cover. Establish a finger in directing колодок in an order, the return to removal.
If there were signs of ageing of rubber, replace protective covers of directing fingers.

8. Establish brake колодки the forward brake mechanism in an order, the return to removal. For an exception самоотворачивания a bolt of fastening of a support before installation grease its carving анаэробным with a carving clamp.
9. Press some times a brake pedal to bring brake колодки to a disk.
10. Establish a wheel.
11. Similarly replace brake колодки the brake mechanism of the right wheel.
12. Check up and if necessary restore level of a brake liquid in a tank of the main brake cylinder.

    
GOOD ADVICE
Having replaced worn out brake колодки new, do not hasten to leave at once on brisk highways. It is not excluded that at the first intensive braking you will be unpleasantly amazed by low efficiency of brakes though колодки the firm are established. Brake disks too wear out, and new колодки concern them only with edges, practically without braking. Choose a silent small street or journey without cars and some times smoothly brake, that колодки have got used and began to adjoin all surface. At the same time estimate also efficiency of brakes.
Try not to brake sharply at least the first 100 km. At strong heating not earned extra колодок the top layer of their overlays burns slightly also brakes still for a long time will not be as much as possible effective.


The previous page
9.9. Brake mechanisms of forward wheels
The following page
9.9.2. Replacement of a support of the forward brake mechanism