Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
6. Transmission
7. A running gear
7.1. A forward suspension bracket
7.1.1. Features of a design
7.1.2. Possible malfunctions of a forward suspension bracket, their reason and ways of elimination
7.1.3. Removal and installation absorber racks
7.1.4. Repair absorber racks
7.1.5. Replacement of the top support absorber racks
7.1.6. Replacement of a spherical support absorber racks
7.1.7. Replacement of the lever of a forward suspension bracket
7.1.8. Replacement of details of the stabilizer of cross-section stability of a forward suspension bracket
7.1.9. Replacement of the bearing of a forward nave
7.2. A back suspension bracket
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 








7-1-8-zamena-detalejj-stabilizatora-poperechnojj-ustojjchivosti-perednejj-podveski.html

7.1.8. Replacement of details of the stabilizer of cross-section stability of a forward suspension bracket

It be required to you: keys «on 10», «on 12», face heads «on 12», «on 14», вороток, the extension piece, propeller the hinge.
1. Will hang out a forward part of the car and remove engine mudguards (Removal and installation of mudguards of the engine »see«).
2. Turn away a nut of fastening of a rack of the stabilizer of cross-section stability to a bar, keeping a bolt a face head and воротком.
3. Remove the top washer …
4. … and the rubber plug. If you remove a rack not for replacement, mark before removal an arrangement of other details of a rack to establish them on former places.
5. Putting forward a bolt downwards, remove washers, rubber plugs and распорную the plug of a rack of the stabilizer of cross-section stability.
6. Similarly remove the second rack of the stabilizer.
7. Turn out two bolts of fastening right скобы
8. … also remove скобу fastenings of a bar of the stabilizer …
9. … and the rubber plug.
10. Turn out two bolts left скобы fastenings of a bar of the stabilizer.

    
THE NOTE
For a reversing of bolts of fastening left скобы use the extension piece and propeller the hinge.

11. Remove скобу fastenings of a bar of the stabilizer and the rubber plug.
    
THE NOTE
The damaged or worn out plugs replace new.

12. Turn out bolts of fastening of the first …
13. … and the movement of the car of holders of tubes second for a direction.
14. Remove a bar of the stabilizer from the car. Do not unbend a tube more than it is necessary for removal of a bar of the stabilizer not to damage them.

Fig. 7.3. A stabilizer rack: 1, 6, 11, 12 – washers; 2 – a nut; 3 – a bolt; 4, 8, 9, 13 – rubber plugs; 5 – a stabilizer bar; 7 – распорная the plug; 10 – the bottom lever; In – the assembly size

15. Establish details in an order, the return to removal. The relative positioning of details of a rack is shown on fig. 7.3. Pay attention to a relative positioning and orientation of washers and plugs, ledges of plugs should enter into lever and bar apertures so that the rack bolt did not concern the lever and a bar. Definitively tighten nuts 2 (fig. 7.3 see) before reception of the size In, equal 38 mm, on the car standing on the earth.

THE NOTE
After replacement of details of the stabilizer of cross-section stability check up and if necessary adjust corners of installation of wheels. Take advantage of services of the workshops having the special equipment.

«The previous page
7.1.7. Replacement of the lever of a forward suspension bracket
The following page»
7.1.9. Replacement of the bearing of a forward nave











cf8e4909