Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
11.1. Features of a design
11.2. Possible malfunctions of a body, their reason and ways of elimination
11.3. Removal, dismantling and installation of bumpers
11.4. Removal and installation of facing of a radiator
11.5. Removal and installation of mudguards of wheels and Lockers
11.6. Removal and installation of a forward wing
11.7. Removal and installation of a lattice of a box air flow
11.8. A cowl
11.9. Doors
11.10. A luggage carrier cover
11.11. A cover of the hatch of a bulk pipe of a fuel tank
11.12. Seats
11.13. Removal and installation of facing of a tunnel of a floor
11.14. System of passive safety (SRS)
11.14.1. Features of a design
11.14.2. Removal and installation of a pillow of safety of the driver
11.14.3. Replacement of a forward seat belt
11.14.4. Replacement of a back seat belt
11.14.5. Removal and installation of the electronic block of management by additional system of passive safety
11.15. Rear-view mirrors
11.16. The panel of devices
11.17. A heater and the conditioner
11.18. Salon armature
11.19. Removal and installation of facings of salon
11.20. Removal and installation of facings of a luggage carrier
11.21. A screen wiper of a wind window
11.22. Replacement motionless glazing bodies
11.23. Removal and installation of a shelf of fastening of the storage battery
11.24. Care of a body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 








11-14-3-zamena-perednego-remnya-bezopasnosti.html

11.14.3. Replacement of a forward seat belt

THE NOTE
Replacement of forward seat belts is shown on an example of a seat belt of the driver. A seat belt of the forward passenger replace similarly.

It be required to you: keys TORX T30, «on 17», a screw-driver with a crosswise edge.
1. If seat belts are equipped tensionми, disconnect a wire from the plug "minus" of the storage battery.

PREVENTIONS
After a detachment of a wire from the plug it is necessary to wait "minus" of the storage battery not less than 10 mines and only after that it is possible to start removal of the seat belt equipped retractors.
Dismantling преднатяжителей belts is forbidden.
Falling of coils of belts with tensionми and hit in them waters and oils is not supposed.
Influence on преднатяжители temperature belts above 95 °С is not supposed.

2. Remove the bottom part of facing of the central rack (Removal and installation of facings of salon »see«).

    
THE NOTE
The seat of the driver is for descriptive reasons removed.

3. Turn out two screws of fastening directing a belt to the central rack.
4. Remove a decorative cap from the bottom bolt of fastening of a belt …
5. … also turn out a bolt.

    
THE PREVENTION
On bolts of fastening of a belt washers and remote plugs are established, do not lose them.

6. Cast away a decorative overlay of a buckle …
7. … also turn out a bolt of the top fastening of a belt.
8. Turn out the screw of fastening of the inertial coil …
9. … also take the coil from a body rack.
10. Before removal of the lock of a forward seat belt separate pad a plait of wires of an alarm lamp of not fastened seat belt (if you remove a seat belt of the driver).
11. Turn out a bolt of fastening of the lock of a seat belt to a seat …
12. … also remove the lock.
13. Establish a forward seat belt in an order, the return to removal.

«The previous page
11.14.2. Removal and installation of a pillow of safety of the driver
The following page»
11.14.4. Replacement of a back seat belt











cf8e4909