Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
11.1. Features of a design
11.2. Possible malfunctions of a body, their reason and ways of elimination
11.3. Removal, dismantling and installation of bumpers
11.4. Removal and installation of facing of a radiator
11.5. Removal and installation of mudguards of wheels and Lockers
11.6. Removal and installation of a forward wing
11.7. Removal and installation of a lattice of a box air flow
11.8. A cowl
11.9. Doors
11.10. A luggage carrier cover
11.11. A cover of the hatch of a bulk pipe of a fuel tank
11.12. Seats
11.13. Removal and installation of facing of a tunnel of a floor
11.14. System of passive safety (SRS)
11.15. Rear-view mirrors
11.16. The panel of devices
11.17. A heater and the conditioner
11.18. Salon armature
11.19. Removal and installation of facings of salon
11.20. Removal and installation of facings of a luggage carrier
11.21. A screen wiper of a wind window
11.22. Replacement motionless glazing bodies
11.23. Removal and installation of a shelf of fastening of the storage battery
11.24. Care of a body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 








11-5-snyatie-i-ustanovka-bryzgovikov-koles-i-podkrylkov.html

11.5. Removal and installation of mudguards of wheels and Lockers

In arches of forward wheels and in a back part of arches of back wheels are established plastic подкрылки, protecting a body from abrasive influence of sand and the stones rejected by wheels. The mudguards established behind forward wheels, protect body thresholds. Back mudguards protect the cars, going trace, from damage by stones taking off from under back wheels.
It be required to you: a screw-driver with a crosswise edge, a key-rattle with a crosswise bat for отворачивания remote screws.

    
THE NOTE
Work is shown for mudguards and Lockers on the left side of the car. The right mudguards and подкрылки remove and establish similarly.

For removal of a mudguard of a forward wheel execute following operations.
1. Turn out the screw of the bottom fastening …
2. … and two screws of forward fastening of a mudguard to a forward wing …
3. … then remove a mudguard of a forward wheel.
4. Establish a mudguard of a forward wheel in an order, the return to removal.

For removal forward подкрылка execute following operations.
1. Remove a mudguard of a forward wheel (see above in the given subsection).
2. Turn out three screws of fastening подкрылка to a forward bumper.
3. Push (for example, a screw-driver) the core of a percussion cap of forward fastening подкрылка in a percussion cap …
4. … also remove a percussion cap.
5. Similarly remove two percussion caps of the top fastening …
6. … on one percussion cap of back fastening above …
7. … and below …
8. … then remove forward подкрылок.
9. Establish forward подкрылок in an order, the return to removal.

For removal of a mudguard of a back wheel execute following operations.
1. Turn out the screw of the bottom fastening …
2. … and two screws of forward fastening of a mudguard to a back bumper …
3. … also remove a mudguard of a back wheel.
4. Establish a mudguard of a back wheel in an order, the return to removal.

For removal back подкрылка execute following operations.
1. Remove a mudguard of a back wheel (see above in the given subsection).
2. Turn out two top screws …
3. … and one bottom screw of fastening подкрылка to a back bumper …
4. … then remove back подкрылок.
5. Establish back подкрылок and all removed details in an order, the return to removal.

«The previous page
11.4. Removal and installation of facing of a radiator
The following page»
11.6. Removal and installation of a forward wing











cf8e4909