Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
11.1. Features of a design
11.2. Possible malfunctions of a body, their reason and ways of elimination
11.3. Removal, dismantling and installation of bumpers
11.4. Removal and installation of facing of a radiator
11.5. Removal and installation of mudguards of wheels and Lockers
11.6. Removal and installation of a forward wing
11.7. Removal and installation of a lattice of a box air flow
11.8. A cowl
11.9. Doors
11.10. A luggage carrier cover
11.11. A cover of the hatch of a bulk pipe of a fuel tank
11.12. Seats
11.13. Removal and installation of facing of a tunnel of a floor
11.14. System of passive safety (SRS)
11.14.1. Features of a design
11.14.2. Removal and installation of a pillow of safety of the driver
11.14.3. Replacement of a forward seat belt
11.14.4. Replacement of a back seat belt
11.14.5. Removal and installation of the electronic block of management by additional system of passive safety
11.15. Rear-view mirrors
11.16. The panel of devices
11.17. A heater and the conditioner
11.18. Salon armature
11.19. Removal and installation of facings of salon
11.20. Removal and installation of facings of a luggage carrier
11.21. A screen wiper of a wind window
11.22. Replacement motionless glazing bodies
11.23. Removal and installation of a shelf of fastening of the storage battery
11.24. Care of a body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 








11-14-2-snyatie-i-ustanovka-podushki-bezopasnosti-voditelya.html

11.14.2. Removal and installation of a pillow of safety of the driver

The pillow of safety of the driver should be removed at repair of elements of a steering and a car electric equipment. Therefore process of its removal and installation is described in the given management. However in order to avoid reception of traumas strictly adhere to recommended sequence of work.
It be required to you: key TORX T50, a screw-driver with a flat edge.
1. Disconnect a wire from the plug "minus" of the storage battery.
    
PREVENTIONS
Attempt of removal of the module of a pillow of safety without switching-off of the storage battery can lead to unexpected operation of a pillow.
To start following operations on removal of a pillow of safety it is possible only after the full category of the condenser of the activator. For the condenser category it is necessary to wait not less than 15 mines after a detachment of a wire from the plug "minus" of the storage battery.
Dismantling of the module of a pillow of safety is forbidden.
Falling of the module of a pillow of safety and hit on it waters, greasings or oils is not supposed.
Influence on the module of a pillow of safety of temperature above 95 °С is not supposed.

2. Having hooked a screw-driver, remove заглушки on steering wheel facing at the left …
3. … and on the right.
4. Turn out screws of fastening of a pillow of safety to a steering wheel nave at the left …
5. … and on the right.
6. Accurately raise the module of a pillow of safety …
7. … take away it from a steering wheel nave, having pressed a clamp, disconnect pad wires of switches of sound signals …
8. … unfasten a clamp колодки a plait of wires of a pillow of safety …
9. … disconnect pad wires from the pillow module …
10. … also remove the module of a pillow of safety.
11. Establish a safety pillow in an order, the return to removal.

«The previous page
11.14.1. Features of a design
The following page»
11.14.3. Replacement of a forward seat belt











cf8e4909