Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
11.1. Features of a design
11.2. Possible malfunctions of a body, their reason and ways of elimination
11.3. Removal, dismantling and installation of bumpers
11.4. Removal and installation of facing of a radiator
11.5. Removal and installation of mudguards of wheels and Lockers
11.6. Removal and installation of a forward wing
11.7. Removal and installation of a lattice of a box air flow
11.8. A cowl
11.9. Doors
11.10. A luggage carrier cover
11.10.1. Replacement торсионов luggage carrier covers
11.10.2. Removal and installation of a cover of a luggage carrier
11.10.3. Replacement of the lock, a latch and the switch of the lock of a cover of a luggage carrier
11.10.4. Removal and installation of a drive of the lock of a cover of a luggage carrier
11.10.5. Removal and installation of a decorative overlay of a cover of a luggage carrier
11.11. A cover of the hatch of a bulk pipe of a fuel tank
11.12. Seats
11.13. Removal and installation of facing of a tunnel of a floor
11.14. System of passive safety (SRS)
11.15. Rear-view mirrors
11.16. The panel of devices
11.17. A heater and the conditioner
11.18. Salon armature
11.19. Removal and installation of facings of salon
11.20. Removal and installation of facings of a luggage carrier
11.21. A screen wiper of a wind window
11.22. Replacement motionless glazing bodies
11.23. Removal and installation of a shelf of fastening of the storage battery
11.24. Care of a body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 








11-10-3-zamena-zamka-zashhelki-i-vyklyuchatelya-zamka-kryshki-bagazhnika.html

11.10.3. Replacement of the lock, a latch and the switch of the lock of a cover of a luggage carrier

It be required to you: a key «on 10» (the face head is more convenient), a screw-driver with a flat edge.
1. For removal of the lock of a cover of a luggage carrier remove facing of the panel of a back (Removal and installation of facings of a luggage carrier »see«).
2. From within a luggage carrier turn out two bolts of fastening of the lock to the amplifier of the panel of a back …
3. … also deduce the lock outside through a window in the panel.
4. Deduce a tip of a cable of a drive of the lock from a lever cut …
5. … a tip of a cover of a cable from a cut of the case of the lock also remove the lock.
6. Will put the lock in an order, the return to removal.
7. If the lock indistinctly locks a cover of a luggage carrier or, on the contrary, unlocks with difficulty, adjust length of a cover of a cable of a drive of the lock for what through a window in the amplifier of the panel of a back take a tip of a cover from a cut of the case of the lock and rearrange it in other position. At indistinct lock-out of the lock move a tip in a direction of the lever of the lock, at the complicated unlocking — in an opposite direction.
8. Establish facing of the panel of a back (Removal and installation of facings of a luggage carrier »see«).
9. If захлопывание luggage carrier covers it is accompanied by latch blow about the lock lever, adjust lock position, for what from within a luggage carrier ослабьте two bolts of fastening of the lock …
10. … and, moving the lock in a cross-section direction, achieve unaccented захлопывания. Then tighten bolts of fastening of the lock.
11. For removal of a latch of the lock of a luggage carrier from within luggage carrier covers unfasten a clamp of draught of the switch of the lock …
12. … also disconnect draught from the switch lever.
13. Disconnect a wire from the trailer switch of a latch.
14. Turn out two screws of fastening of a latch to the amplifier of a cover of a luggage carrier …

    
THE NOTE
The right screw of fastening of a latch simultaneously fixes also "a mass" wire. Do not forget to establish it into place at return installation of a latch.

15. … also remove a latch.
16. If a latch have removed for replacement, disconnect from its lever draught of an external drive, having unfastened a draught clamp, and rearrange draught on a new latch.
17. Establish a latch of the lock of a luggage carrier and all removed details to an order, the return to removal.
18. For removal of the switch of the lock of a luggage carrier disconnect from its lever bent for to a lock latch (subitem 11 and 12 see).
19. Turn on two nuts of fastening of the switch to the external panel of a cover of a luggage carrier …
20. … also remove the switch.
21. For replacement of the cylinder or a switch spring remove from a cylinder shaft a lock washer, having hooked its screw-driver.
22. Insert a key into the switch cylinder …
23. … remove from a shaft the lever 1 and if necessary a spring 2 from the switch case.
24. Take the cylinder from the switch case.
25. Collect and establish the switch of the lock of a cover of a luggage carrier and all removed details in an order, the return to removal.

    
THE NOTE
Before switch assemblage grease its cylinder with silicone greasing.

«The previous page
11.10.2. Removal and installation of a cover of a luggage carrier
The following page»
11.10.4. Removal and installation of a drive of the lock of a cover of a luggage carrier











cf8e4909