Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
6. Transmission
7. A running gear
7.1. A forward suspension bracket
7.1.1. Features of a design
7.1.2. Possible malfunctions of a forward suspension bracket, their reason and ways of elimination
7.1.3. Removal and installation absorber racks
7.1.4. Repair absorber racks
7.1.5. Replacement of the top support absorber racks
7.1.6. Replacement of a spherical support absorber racks
7.1.7. Replacement of the lever of a forward suspension bracket
7.1.8. Replacement of details of the stabilizer of cross-section stability of a forward suspension bracket
7.1.9. Replacement of the bearing of a forward nave
7.2. A back suspension bracket
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 



cf8e4909





7-1-3-snyatie-i-ustanovka-amortizatornojj-stojjki.html

7.1.3. Removal and installation absorber racks

It be required to you: keys on 9, on 12, on 19, face heads on 32, a key for bolts of wheels, вороток, a stripper of spherical hinges, small beards, a hammer.
1. Brake the car a lay brake and establish противооткатные an emphasis ("boots") under back wheels.
2. Loosen the an inhaling of a nut of fastening of a nave.
3. Loosen the an inhaling of bolts of fastening of a wheel.
    
THE PREVENTION
Weaken and tighten bolts of fastening of a wheel only on the car standing on the earth.

4. Open a cowl, hook a screw-driver …
5. … also remove a protective cover of the top support of a telescopic rack.
6. Keeping one key a rod of the shock-absorber from проворачивания, the second key ослабьте a nut inhaling (if you remove a telescopic rack for replacement of the shock-absorber, a spring or the top support).
7. Loosen the an inhaling of three nuts of fastening of the top support.
8. Raise a forward part of the car and establish on reliable support.
9. Remove a wheel.
10. Turn out bolts of fastening of a support, remove a support in gathering (Replacement of a support of the forward brake mechanism see), without disconnecting a brake hose, and suspend it on a wire.
11. Turn out the lock screw and remove a brake disk (Replacement of a brake disk see).
12. Turn away a nut of a finger of a tip of steering draught and выпрессуйте a finger from the rotary lever of a telescopic rack (Replacement of an external tip of steering draught see).
13. Remove a spring clamp of a nut of fastening of a finger of a spherical support, turn away a nut and выпрессуйте a finger (Replacement of a spherical support absorber racks see).
14. Turn away a nave nut …
15. … remove a washer, deduce a shaft of the external hinge of equal angular speeds from a nave of a wheel and suspend a drive of a forward wheel on a wire.
    
THE PREVENTION
At work be cautious not to damage a protective cover of the SHRUS, as work on its replacement very labour-consuming.

16. Definitively turn away three nuts of fastening of the top support to a body, remove washers (if are established) and remove a telescopic rack in gathering.
17. Establish a telescopic rack in an order, the return to removal. A nave nut definitively tighten on the car standing on the earth, the moment specified in the appendix 1.
18. After an inhaling stop a nut бородком and a hammer.

THE NOTE
After replacement of a telescopic rack of a forward suspension bracket or its details check up and if necessary adjust corners of installation of wheels (Check and adjustment of corners of installation of wheels see). Take advantage of services of the workshops having the special equipment.

The previous page
7.1.2. Possible malfunctions of a forward suspension bracket, their reason and ways of elimination
The following page
7.1.4. Repair absorber racks