Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
5.1. Features of a design
5.2. Compression check in cylinders
5.3. Removal and installation of mudguards of the engine
5.4. Replacement of support of a suspension bracket of the power unit
5.5. Installation of the piston of the first cylinder in position ВМТ of a step of compression
5.6. Removal, installation and дефектовка a flywheel
5.7. Replacement of details of consolidation of the engine
5.8. A head of the block of cylinders
5.9. Removal and engine installation
5.10. Engine repair
5.11. Greasing system
5.12. Cooling system
5.13. System of release of the fulfilled gases
5.14. The engine power supply system
5.14.1. Features of a design
5.14.2. Pressure check in the engine power supply system
5.14.3. Pressure decrease in the power supply system
5.14.4. Removal and installation of the air filter, the muffler of noise of an admission and an air line
5.14.5. Replacement of the fuel pump
5.14.6. Replacement of a fuel tank and its bulk pipe
5.14.7. Check and replacement of a regulator of pressure of fuel
5.14.8. Removal and installation of a fuel stage
5.14.9. Removal, installation and check of atomizers
5.14.10. Removal and installation of throttle knot
5.14.11. Check and replacement of a regulator of idling
5.14.12. Adjustment and replacement of a cable of a drive throttle заслонки
5.14.13. Removal and installation of a pedal of an accelerator
5.15. System of catching of steams of fuel
5.16. System рециркуляции the fulfilled gases
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 



cf8e4909





5-14-8-snyatie-i-ustanovka-toplivnojj-rampy.html

5.14.8. Removal and installation of a fuel stage

Fuel stage remove for replacement at damage (breakage of unions), for replacement of atomizers or for access reception to other knots.
It be required to you: keys on 10, on 12.
1. Lower pressure in the power supply system (Pressure decrease in the power supply system see).
2. Disconnect from the fuel filter a hose of giving of fuel in a fuel stage, having compressed its clamp (Replacement of the fuel filter see).
    
THE NOTE
Necessity of a detachment of a hose from the fuel filter, instead of from a stage is caused by that for its detachment from a stage the special adaptation (the good advice see more low) is required, to use which expediently only at hose or stage replacement.

GOOD ADVICE
The tip of a hose of giving of fuel in a stage is fixed on the stage union цанговым by a clip. For easing of this clip it is necessary to get the special adaptation or to make it by own strength as it is described more low.
Wrap up the union of a stage a tin strip, having made similarity of the plug …
… move the plug into a hose tip so that it was possible to unclench pads цангового a clip …
… also disconnect a tip of a hose from the stage union.

3. Remove from the union of a regulator of pressure of fuel a vacuum hose.
4. Disconnect from a regulator of pressure a hose fuel plum, having compressed its clamps.
5. Move upwards a clamp колодки a plait of wires of an atomizer …
6. … also disconnect pad. Similarly disconnect колодки a plait of wires from other atomizers and take a plait of atomizers aside.
7. Turn out two bolts of fastening of an arm of a cable of a drive throttle заслонки to an inlet pipe …
8. … also take a cable aside together with an arm.
9. Turn out two bolts of fastening of a fuel stage to an inlet pipe …
10. … also remove a stage, taking out atomizers from apertures of an inlet pipe.
    
THE PREVENTION
If at stage removal any of atomizers remains in an inlet pipe, necessarily replace a clamp of this atomizer.

11. If necessary remove from an atomizer stage (Removal, installation and check of atomizers see) and a regulator of pressure of fuel (Check and replacement of a regulator of pressure of fuel see).
    
THE NOTE
Sealing rings of atomizers replace new at each removal or dismantling of a fuel stage.

12. Establish a fuel stage in sequence, to return dismantling and removal, having greased sealing rings of atomizers with engine oil.
13. Having connected pipelines to a stage, start up the engine and check up tightness of connections of pipelines and consolidations of atomizers.

The previous page
5.14.7. Check and replacement of a regulator of pressure of fuel
The following page
5.14.9. Removal, installation and check of atomizers