5-14-6-zamena-toplivnogo-baka-i-ego-nalivnojj-truby.html
5.14.6. Replacement of a fuel tank and its bulk pipeAt detection of leak of fuel from a tank it is recommended to replace a tank. If the grid of the fuel pump often gets littered, remove and wash out a tank.
If the leak in the area of a joint of the top and bottom parts of a tank is found out, it is possible these places пропаять (it is recommended to do in specialised workshops). For this purpose pour out the gasoline rests, carefully wash out and dry a tank. Then a leak place solder soft solder.
PREVENTIONS
It is possible to solder only carefully washed out and dried tank which is not containing steams of gasoline, differently at a pair ration can ignite.
For washing of a fuel tank use washing-up liquids of "Lobomid", МС or ML. To remove the washing-up liquid rests, wash out and пропарьте a tank a stream of hot water. Carefully dry a tank.
It is more convenient to remove an empty tank, working on the lift, a platform or a viewing ditch. For removal of the rests of fuel remove an electrogasoline pump (Replacement of the fuel pump see) and pump out fuel through opened aperture in a tank.
|
It be required to you: keys on 8, on 12, пассатижи, a screw-driver with a flat edge.
2. Disconnect a wire from the plug "minus" of the storage battery.
|
|
3. Disconnect from pipelines forcing and drain hoses of the fuel pump, having compressed their clamps.
|
4. Separate the pipeline of tap of steams of fuel in an adsorber, having compressed its clamps.
|
|
|
5. Compress clamps and separate pad a plait of wires of the fuel pump.
|
6. Take a cable of a drive of a lay brake from the holders located on a fuel tank in its forward part...
|
|
|
7. … and on the right.
|
8. Loosen the an inhaling of a collar of fastening of a hose of ventilation also disconnect a hose from a branch pipe of a fuel tank.
|
|
|
9. Loosen the a collar of fastening of a hose of a bulk pipe, having compressed пассатижами its unbent ears, shift a collar on a hose and disconnect a hose from a branch pipe of a fuel tank.
|
10. Having established under a fuel tank a support, turn out on two bolts of fastening of a tank to the body basis ahead …
|
11. … and behind.
12. Clean a support and remove a fuel tank from the car.
GOOD ADVICE
Remove a fuel tank with the assistant as the tank heavy enough and has the form inconvenient for keeping.
|
13. Establish a fuel tank in an order, the return to removal.
14. After joining of pipelines and a plait of wires of the fuel pump fill in in a tank gasoline, start up the engine and check up tightness of all connections of pipelines.
If it is necessary to remove a bulk pipe of a fuel tank, execute the following.
1. Remove the right back wheel and establish the car on a reliable support.
|
|
2. Turn out four bolts of fastening of a protective casing of a pipe to a body …
|
3. … also remove a casing.
|
4. Disconnect hoses of a bulk pipe and ventilation from branch pipes of a fuel tank (subitem 8 and 9 these subsections see).
5. Have a bite бокорезами (or knife) a collar of fastening of hoses and pipelines.
THE NOTE
Collar of fastening of hoses and pipelines of disposable use. At assemblage fix hoses and pipelines a new collar.
|
|
|
6. Open the hatch of a mouth of a bulk pipe of a fuel tank and turn out from a mouth a stopper.
|
7. Turn out three bolts of fastening of a bulk pipe to боковине bodies …
|
|
|
8. … a bolt of fastening of an arm of a bulk pipe to the body basis …
|
9. … also remove a bulk pipe in gathering with an arm and a ventilating hose.
|
|
|
10. In need of replacement of a bulk pipe unfasten a screw-driver an arm clamp …
|
11. … also remove an arm …
|
|
|
12. … take sealing plugs from the bottom ends of a bulk pipe …
|
13. … and a ventilating hose, then establish the removed details on a new bulk pipe.
|
14. Establish a bulk pipe of a fuel tank in an order, the return to removal.
|