Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
11.1. Features of a design
11.2. Possible malfunctions of a body, their reason and ways of elimination
11.3. Removal, dismantling and installation of bumpers
11.4. Removal and installation of facing of a radiator
11.5. Removal and installation of mudguards of wheels and Lockers
11.6. Removal and installation of a forward wing
11.7. Removal and installation of a lattice of a box air flow
11.8. A cowl
11.9. Doors
11.10. A luggage carrier cover
11.11. A cover of the hatch of a bulk pipe of a fuel tank
11.12. Seats
11.13. Removal and installation of facing of a tunnel of a floor
11.14. System of passive safety (SRS)
11.15. Rear-view mirrors
11.16. The panel of devices
11.17. A heater and the conditioner
11.18. Salon armature
11.19. Removal and installation of facings of salon
11.20. Removal and installation of facings of a luggage carrier
11.21. A screen wiper of a wind window
11.22. Replacement motionless glazing bodies
11.23. Removal and installation of a shelf of fastening of the storage battery
11.24. Care of a body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 



cf8e4909





11-20-snyatie-i-ustanovka-oblicovok-bagazhnika.html

11.20. Removal and installation of facings of a luggage carrier

The facings of a luggage carrier formed from plastic, are attached to panels of a body by percussion caps. The rug of a trunk floor from a nonwoven carpet material is laid on a trunk floor and also attached to it by four percussion caps located in a forward part of a rug.
The screw-driver with a flat edge is required to you.
1. Facing of a back left lantern is attached to a body by four percussion caps three of which simultaneously attach also a back part of facing of an arch of a back wheel. Take percussion caps …
2. … having hooked a screw-driver …
3. … also remove facing.

    
THE NOTE
Facing of a back right lantern remove similarly.


4. For removal of facing of an arch of a back left wheel remove facing of a back lantern (subitem 1-3 see) as three percussion caps of its fastening simultaneously fix also arch facing …
5. … take a percussion cap of fastening of facing of an arch to a partition of a back of a body …
6. … and two percussion caps of fastening of back facing боковины, simultaneously крепящие and arch facing.
7. Remove facing of an arch of a back left wheel.
    
THE NOTE
Facing of an arch of a back right wheel remove similarly.

8. For removal of facing of the panel of a back take four percussion caps of fastening of its top part …
9. … then, having raised a back edge of a rug of a luggage carrier and a cover of a niche for the spare wheel, two percussion caps at the left and on the right facing fastenings to body longerons …
10. … and one percussion cap of fastening of facing to a trunk floor, located on the centre.
11. Remove facing of the panel of a back.
12. For removal of a rug of a trunk floor take four percussion caps of its fastening located along a forward edge of a rug.
13. Establish facings of a luggage carrier and a floor rug in an order, the return to removal.

The previous page
11.19. Removal and installation of facings of salon
The following page
11.21. A screen wiper of a wind window