Chevrolet Lanos (since 2004 of release)
1. The car device
2. Recommendations about operation
3. Malfunctions in a way
4. Maintenance service
5. The engine
6. Transmission
7. A running gear
8. A steering
9. Brake system
10. An electric equipment
11. A body
11.1. Features of a design
11.2. Possible malfunctions of a body, their reason and ways of elimination
11.3. Removal, dismantling and installation of bumpers
11.4. Removal and installation of facing of a radiator
11.5. Removal and installation of mudguards of wheels and Lockers
11.6. Removal and installation of a forward wing
11.7. Removal and installation of a lattice of a box air flow
11.8. A cowl
11.9. Doors
11.10. A luggage carrier cover
11.11. A cover of the hatch of a bulk pipe of a fuel tank
11.12. Seats
11.13. Removal and installation of facing of a tunnel of a floor
11.14. System of passive safety (SRS)
11.15. Rear-view mirrors
11.16. The panel of devices
11.17. A heater and the conditioner
11.18. Salon armature
11.19. Removal and installation of facings of salon
11.20. Removal and installation of facings of a luggage carrier
11.21. A screen wiper of a wind window
11.22. Replacement motionless glazing bodies
11.23. Removal and installation of a shelf of fastening of the storage battery
11.24. Care of a body
12. Wheels and tyres
13. Purchase of spare parts
14. A trip on HUNDRED
15. Winter operation of the car
16. Preparation for checkup
17. Councils to the beginning mechanic
18. Appendices
19. Electric equipment schemes
 



cf8e4909





11-19-snyatie-i-ustanovka-oblicovok-salona.html

11.19. Removal and installation of facings of salon

It be required to you: screw-drivers with flat and crosswise edges.

    
THE NOTE
Removal and installation of facings on the left side of salon are shown. Facings on the right side remove similarly.

1. Before removal of facing of a rack of a wind window remove from edge of a rack a doorway sealant as it blocks a facing edge.
2. Remove facing of a rack of a wind window, overcoming resistance of percussion caps of its fastening.

    
THE NOTE
Examine percussion caps of fastening of facing. The broken percussion caps replace.

3. Turn out the holder of forward facing боковины
4. … also remove facing.
5. For removal of forward facing of a threshold, having pulled it upwards, take from apertures of arms percussion caps of its fastening and then, having removed the spring holders established in grooves of facing, with отбортовки a threshold, remove facing.



THE NOTE
The forward end of forward facing of a threshold is established under back edge of forward facing боковины. If removal of forward facing of a threshold is complicated, turn out the holder of facing боковины (item 3 see) to release threshold facing.

6. For removal of back facing of a threshold turn out the screw of its fastening to the body basis …
7. … and, having pulled it upwards, take from apertures of arms percussion caps of its fastening. Then, having removed the spring holders established in grooves of facing, with отбортовки a threshold, remove facing.
8. Before removal of the bottom part of facing of the central rack remove forward and back facings of a threshold (subitem 5 and 7 see). Then, a few having bent edges of the bottom part of facing of the central rack, remove them with отбортовок racks …

9. … also remove the bottom part of facing.
10. Before removal of the top part of facing of the central rack remove the bottom part of facing (item 9 see), turn out two screws of fastening directing a seat belt and disconnect from the central rack the top fastening of a belt (subitem 3 and 6 Replacement of a forward seat belt see). Then take away from a rack a bottom edge of the top part of facing …

11. … having hooked a screw-driver, deduce its upper edge from under an upholstery of a ceiling and remove the top part of facing.
12. Before removal of facing of a shelf of a back remove a back of a back seat (Removal and installation of a back seat see)...
13. … and in a luggage carrier separate pad a plait of wires of an additional stoplight.

    
THE NOTE
Facing is attached to a shelf of a back by six percussion caps.

14. Take on three percussion caps forward …
15. … and the top fastenings of facing of a shelf of a back …
16. … also remove facing in gathering with an additional stoplight.
17. If necessary remove from facing an additional stoplight, having turned on two nuts of its fastening (Replacement of an additional stoplight see).
18. Disconnect facing from a back rack, overcoming resistance of percussion caps of its fastening.

    
THE NOTE
Examine percussion caps of fastening of facing. The broken percussion caps replace.

19. Disconnect the top and bottom fastenings of a seat belt (Replacement of a back seat belt see).
20. Overcoming effort of clamps, take from an aperture of facing an aperture fringing.
21. Pass an aperture fringing together with a belt buckle in a facing aperture …
22. … also remove facing from a seat belt.
23. Before removal of back facing боковины remove back facing of a threshold (subitem 6 see and 7 in the given subsection), facing of a back rack (subitem 18-22 in the given subsection see) and a seat belt of the lateral passenger on a back seat (Replacement of a back seat belt see).
24. Take two percussion caps of fastening of back facing боковины to a body …
25. … also remove facing.
26. Establish facings of salon and all removed details in an order, the return to removal.

The previous page
11.18.2. Replacement противосолнечных peaks
The following page
11.20. Removal and installation of facings of a luggage carrier